A bike gear calculator for every chainring and cog
This bike gear calculator lays out every gear on your bike in one table. For each chainring and cog pair you get the gear ratio, the gear inches, the development (rollout) in metres and your speed at the cadence you choose, in mph or km/h. It also flags duplicate gears, shows the step between neighbouring cogs and draws a chart of the whole range.
Use it to pick a cassette before a hilly sportive, to check that a 1× mountain bike has a low enough climbing gear, or as a cadence speed calculator: how fast you go at 90 rpm, or which cadence you need to hold 20 mph.
How to use it
- In "Chainrings (teeth)", type one to three chainrings separated by a slash:
50/34,48/36/26, or just32for a single ring. - In "Cassette (cog teeth)", type up to 12 cogs separated by dashes, or click one of the "Common cassettes": 11-28, 11-32, 11-34, 11-42 or 10-51.
- Pick a "Wheel and tire": 700×25C, 700×28C, gravel 700×40C, 29, 27.5 or 26 inch MTB, or a 20 inch wheel. The "Wheel circumference (mm)" fills in by itself. If you have measured your own wheel, type the value and the list switches to "Custom circumference".
- Set the "Cadence (rpm)", 90 by default, and choose mph or km/h.
- Tick "Compare with a second drivetrain" to enter drivetrain B. The chart then shows both setups.
The "Cadence needed for a speed" box takes a chainring, a cog and a "Target speed" and returns the cadence in rpm.
Formulas and worked examples
gear inches = chainring ÷ cog × wheel diameter in inches
development (m) = chainring ÷ cog × circumference (mm) ÷ 1000
speed (km/h) = development × cadence × 60 ÷ 1000, and mph = km/h ÷ 1.609344.
With a 700×25C tire, whose circumference is 2,105 mm (a wheel diameter of 26.4 inches):
| Gear | Ratio | Gear inches | Development | Speed at 90 rpm |
|---|---|---|---|---|
| 50×11 | 4.55 | 119.9 | 9.57 m | 32.1 mph (51.7 km/h) |
| 50×17 | 2.94 | 77.6 | 6.19 m | 20.8 mph (33.4 km/h) |
| 34×28 | 1.21 | 32.0 | 2.56 m | 8.6 mph (13.8 km/h) |
Holding 30 km/h in 50×17 takes 30 × 1000 ÷ 60 ÷ 6.19, or 80.8 rpm. For 20 mph in the same gear you need 86.6 rpm.
Duplicate gears. Two gears on different chainrings are flagged when their development is less than 2% apart. With 50/34 and an 11-28 cassette, 50×25 and 34×17 both give exactly 4.21 m, and 50×19 (5.54 m) is only 0.62% away from 34×13 (5.51 m). Out of 22 combinations, 19 gears are truly distinct.
Steps between cogs. The "Step from previous cog" column shows how much your cadence drops when you shift. Going from 11 to 12 teeth is a 9.1% step. On a 10-51 cassette, the last jump from 42 to 51 teeth is 21.4%.
Single chainring. A 1×12 mountain bike with a 32 tooth ring, a 10-51 cassette and 29 inch wheels (2,288 mm) runs from 18.0 to 91.8 gear inches, or 1.44 m to 7.32 m of development. Its gear range is 510%, against 374% for a 50/34 with an 11-28.
Frequently asked questions
What are gear inches?
Gear inches is the old way of comparing gears in the US and UK: the gear ratio multiplied by the wheel diameter in inches. A higher number means a harder gear. Development in metres is the distance covered per pedal turn.
Why are some gears marked "≈"?
Their development is within 2% of a gear on another chainring. You will hardly feel the difference, so one of them adds nothing to your range.
Which wheel circumference should I use?
The presets give typical values, such as 2,105 mm for 700×25C and 2,136 mm for 700×28C. For more accuracy, roll the bike one full turn with your weight on it, measure the distance in millimetres and type it in.
How do I compare my bike with a new cassette?
Keep your current setup as drivetrain A, tick "Compare with a second drivetrain" and enter the new cassette as B. The summary compares lowest and highest gears, range and distinct gears.