SuperDevTools

Tire Size Calculator and Comparison

Enter your original tire size and the replacement size: diameters, differences, true speed at the speedometer and equivalent sizes appear at once.

Original size

Accepted formats: 205/55 R16, P205/55R16, 205 55 16 and flotation sizes such as 31x10.50R15. A service description like 91V is read too.

Replacement size

Accepted formats: 205/55 R16, P205/55R16, 205 55 16 and flotation sizes such as 31x10.50R15. A service description like 91V is read too.

MeasurementOriginal sizeReplacement sizeDifference

Common rule of thumb: keep the overall diameter within about -3% and +1.5% of the original. It does not replace the sizes approved for your vehicle, listed on the door placard or in the owner's manual.

True speed at the speedometer

Speedometer readsActual speedDifference
Both tires to scale

Equivalent tire sizes

Common sizes (widths 135 to 335, aspect ratios 25 to 85, wheels 12 to 22) whose diameter stays within -3% and +1.5% of the original, closest first.

SizeOverall diameterDifferenceCompare

Read the sidewall markings

After the size, the sidewall shows the load index and speed rating (91V), then the date of manufacture at the end of the DOT code (4 digits: week, then year).

Load index 60 to 120 (per tire)
Speed ratings (maximum speed)

Older ZR or VR markings inside the size mean a tire rated above 149 mph (240 km/h) or 130 mph (210 km/h).

Compare two tire sizes before you buy

Planning bigger wheels or winter tires? This tire size calculator puts an "Original size" next to a "Replacement size". For each one it works out the section width, sidewall height, overall diameter in millimeters and inches, circumference and revolutions per mile. It then shows the difference between the two, your actual speed when the speedometer reads 30, 60 or 70 mph, and the change in ground clearance. A scale drawing lays one tire over the other, and the "Equivalent tire sizes" list suggests common sizes that stay close to the original diameter. Your recent sizes are remembered on your device.

How to use it

  1. Type the size printed on your current tires in "Original size", such as 225/65 R17, P225/65R17 or 225 65 17. Flotation sizes like 31x10.50R15 work too. You can also fill in "Width (mm)", "Aspect ratio (%)" and "Wheel (inches)".
  2. Do the same in "Replacement size". "Swap the two sizes" switches them around.
  3. Read the diameter difference, shown in green, orange or red, and the "True speed at the speedometer" table.
  4. In "Equivalent tire sizes", filter by "Wheel" and click "Compare" to load a size.
  5. Under "Read the sidewall markings", enter a code like 98H or the four-digit DOT date.

How to read a tire size

Take 225/65 R17 98H. 225 is the section width in millimeters. 65 is the aspect ratio: the sidewall is 65% of the width, so 225 × 0.65 = 146.25 mm. R means radial construction. 17 is the wheel diameter in inches, or 17 × 25.4 = 431.8 mm. 98 is the load index, up to 750 kg (about 1,653 lb) per tire, and H is the speed rating, up to 130 mph.

The overall diameter is the wheel plus two sidewalls: 431.8 + 2 × 146.25 = 724.3 mm, or 28.52 inches. Multiply by π and you get a circumference of 2,275.5 mm, which means about 707.3 revolutions per mile.

Flotation sizes give the numbers in inches: a 31x10.50R15 tire is 31 inches tall (787.4 mm) and 10.5 inches wide (266.7 mm) on a 15-inch wheel, leaving a 203.2 mm sidewall.

Why overall diameter matters

Your speedometer and odometer count wheel revolutions and assume a fixed diameter. A taller tire covers more ground per turn, so the speedometer reads lower than your real speed and the odometer logs fewer miles than you drive. A shorter tire does the opposite. Factory speedometers usually read slightly high, and a taller tire can cancel out that margin, which is why the upper limit is tighter than the lower one.

Anti-lock braking and stability control systems compare the speed of each wheel, so mixed diameters can confuse them. A different diameter also changes ground clearance, effective gearing and the room left in the wheel well.

Finally, every vehicle has approved sizes, listed on the door placard or in the owner's manual. A size outside that list may cause trouble with your insurer or at a safety inspection. The -3% to +1.5% range used here is a common rule of thumb among tire shops; it never replaces the sizes approved for your vehicle.

Worked example: 225/65 R17 to 235/65 R17

Measurement225/65 R17235/65 R17
Sidewall height146.25 mm152.75 mm
Overall diameter724.3 mm (28.52 in)737.3 mm (29.03 in)
Revolutions per mile707.3694.8

Going up just one width step adds 13 mm of diameter, a +1.80% difference, which is outside the usual range and shown in red. When the speedometer reads 60 mph you are actually doing 61.08 mph, and 71.26 mph at an indicated 70. Ground clearance rises by 6.5 mm (0.26 in). If you want bigger wheels instead, 225/60 R18 measures 727.2 mm, only +0.40% and shown in green.

Narrower winter tires

Many drivers fit a narrower winter tire on a smaller wheel: it bites better into snow and the set often costs less. For a car on 225/45 R18, a 205/55 R17 measures 657.3 mm against 659.7 mm, a difference of -0.36%. At an indicated 60 mph you would be doing 59.78 mph. Check that the 17-inch wheel clears the brakes and that the size is approved for the vehicle, and never go below the original load index.

The last four digits of the DOT code give the week and year of manufacture. 0721 means week 7 of 2021, the week starting February 15, 2021. The calculator turns that into the tire's approximate age.

Frequently asked questions

How much diameter difference is acceptable?

A common rule of thumb is about -3% to +1.5%. The calculator shows green between -2% and +1%, orange up to the limits and red beyond. Only the sizes approved for your vehicle are binding.

Why does the list include sizes I cannot find?

It combines widths from 135 to 335, aspect ratios from 25 to 85 and wheels from 12 to 22, and not every combination is made. Keep "Similar widths only (± 30 mm)" checked and filter by wheel size.

Do all four tires need to be the same size?

Both tires on the same axle must match. Different sizes front and rear are only fine when the vehicle came that way from the factory.

Does the result account for tread wear?

No. The figures are the nominal dimensions of a new tire; a worn tire is a few millimeters shorter.