A spirit level on your phone, no app needed
This bubble level online reads the tilt sensor in your phone and tells you whether a surface is level. It runs in the browser, so there is nothing to install and no data leaves your device. You get a bubble like a real spirit level, the angle in degrees and the grade in percent, on one or two axes. Handy when the toolbox level is out in the garage and you need to hang a shelf, straighten a picture frame or level a washing machine.
How to use it
- Open the page on your phone. Some phones ask for permission: tap “Enable the sensor” and allow it.
- Pick the “Phone position”. “Flat”: the phone lies on its back, the round bubble shows two axes, “Left-right” and “Front-back”. “On its edge”: the phone stands on its long side against a frame or a stud, and the tube bubble shows one axis.
- Read the tilt, the grade and which side is lower. Between −0.5° and +0.5° the level turns green and shows “Level”.
- Tap “Hold reading” to keep the value on screen while you pick the phone up, then “Resume reading”. On a keyboard, the space bar does the same.
“Smoothing” calms a jittery display: “Strong” is steadier, “None” reacts instantly. Tick “Vibrate when level” to feel the moment the bubble centers, and “Keep screen on” to stop the screen from sleeping during a long job, where the browser allows it.
Calibrate for better accuracy
Accuracy depends on each phone's sensor, which is often slightly off. After calibration you can often expect a few tenths of a degree, with no guarantee. The calibration stays saved on your device.
- “Set zero”: place the phone on a surface you know is level and tap the button. That surface becomes the reference.
- “Calibrate in 2 positions”: no reference surface needed. Tap the button, turn the phone 180° on the same spot, then tap “Reading 2 after turning”. The real slope flips sign when you turn the phone, the sensor error does not. Read +1.2° then −0.8°, and the offset is (1.2 − 0.8) ÷ 2 = 0.2°, so the true slope is 1.0°.
Degrees and percent grade
Percent grade is the rise per 100 units of run: the tangent of the angle times 100. For small angles, remember 1° ≈ 1.75% and 2% ≈ 1.15°.
| Angle | Grade | Drop over 4 ft |
|---|---|---|
| 0.5° | 0.87% | 0.42 in |
| 1° | 1.75% | 0.84 in |
| 2° | 3.49% | 1.68 in |
Shelves and frames: stand the phone on its edge on top of the shelf and adjust until it reads “Level”. A 4 ft shelf at 0.5° is 0.42 in lower at one end. Washing machine or dryer: lay the phone flat on top and turn the feet until both axes are green; a level machine shakes less on the spin cycle. Patio or deck: for a drainage slope of 1 to 2%, aim for 0.6° to 1.15°.
Frequently asked questions
Why does nothing move on my computer?
Most computers have no tilt sensor, so open this page on a phone. To try the tool anyway, “Demo mode” lets you tilt the bubble with the arrow keys (0.1° per press, 1° with Shift) or by clicking inside the level.
Does a phone case affect the reading?
It can, if the case is curved or the camera bump sticks out. Measure on the edge, or calibrate in 2 positions with the case on.
How accurate is it?
Often a few tenths of a degree after calibration, depending on the sensor. That is fine for shelves and appliances. For tiling, masonry or cabinet installs, double-check with a builder's level.
Why does the bubble shake?
The sensor picks up vibrations and your hand. Set the phone down, wait a second, or switch “Smoothing” to “Strong”.