SuperDevTools

Left right speaker test and stereo test

Start with the volume low. Turn your device volume down before the first test, especially with headphones, then raise it gradually. Every sound stops by itself after 30 seconds.

25 %
Left

–

No sound playing. Pick a test below.

Right

Esc or the space bar also stop the sound. Clicking a test a second time stops it.

Left, right and centre

Bursts of pink noise play on the chosen side. "Centre" should seem to come from the middle, between the two speakers.

Phase test

The same noise plays on both sides. "Out of phase" inverts the right channel: if your speakers are wired correctly, it sounds hollow and vague, with little bass, compared with "In phase".

Sweep 20 Hz → 20 kHz

A pure tone rises from 20 Hz to 20 kHz in 20 seconds, 2 seconds per octave. Note the frequency shown when the sound appears, when something rattles and when you can no longer hear it.

Bass and treble

Bass
Treble

Pure tones on both sides. A small phone or laptop speaker reproduces little or nothing at 30 Hz: that is normal.

Noise

Pink noise has equal energy per octave and sounds deeper and softer. White noise has equal energy per hertz and hisses in the treble.

What about 5.1 surround?

This test covers stereo only. A browser gives no reliable access to the channels of a 5.1 or 7.1 system: depending on the device, it either mixes everything down to two channels or orders the channels differently. A centre or rear speaker test would therefore not be trustworthy.

Check your speakers or headphones in a minute

This left right speaker test plays sound on one side, then the other, so you can confirm that headphones, earbuds or a pair of speakers are connected the right way round. Every sound is created by your browser, nothing is downloaded or recorded, and nothing plays until you click.

How to use it

  1. Turn your device volume down, then set the "Volume" slider (25% on your first visit; your setting is remembered after that).
  2. Click "Left only", then "Right only". Each sound should come only from the side shown.
  3. Try "Centre": the sound should appear in the middle, in front of you. "Alternate left/right" switches sides every second.
  4. The red "Stop sound" button stays visible at the bottom of the screen, and Esc works too. Every sound stops by itself after 30 seconds.

How to read each test

Left, right and centre

The signal is pink noise in short bursts, which is easier to locate than a pure tone. If "Left only" comes out on the right, the headphones are on backwards or the amplifier leads are crossed. If the sound comes from both sides at once, look for a "mono audio" option in your system's accessibility settings, or a balance that is not centred.

Phase test

"In phase" sends the same noise to both sides. "Out of phase" multiplies the right channel by −1. When everything is wired correctly, the out-of-phase version sounds hollow and vague and loses its bass. If "In phase" is the one that sounds like that, one speaker has its + and − wires swapped: follow the marked wire (red or striped) from end to end.

Sweep 20 Hz → 20 kHz

A pure tone rises over 20 seconds, 2 seconds per octave, with the frequency shown live: about 80 Hz at 4 s, 632 Hz at 10 s, 2.5 kHz at 14 s and 10 kHz at 18 s. Note when the sound first appears (the speaker's low limit), when a shelf or window starts to rattle, and when you can no longer hear anything.

Bass, treble and noise

30, 50 and 80 Hz help you judge a subwoofer or bookshelf speakers: buzzing points to a damaged cone or something loose in the room. 8, 12 and 16 kHz check the tweeters. Pink noise helps compare two speakers; white noise reveals hiss.

High frequencies and age

Hearing loses the high frequencies with age: it is a normal, gradual process called presbycusis. Not hearing 16 kHz is very common in adults and does not mean your equipment is faulty. Ask a younger person to listen before you decide. This page is not a hearing test and does not replace a check by a hearing professional.

Safety first

Start low, especially with headphones, and never turn the volume up to "find" a tone you cannot hear: you could harm your ears or a tweeter. There is no 5.1 test because browsers do not give reliable access to centre and rear channels.

Frequently asked questions

I hear nothing at all. What should I check?

Check which output your system is using (Bluetooth headphones still connected, an HDMI monitor), the tab volume and, on a phone, silent mode, which also mutes this sound on some models.

Why does 30 Hz not play on my laptop?

Its small speakers cannot go that low. On headphones or with a subwoofer you should notice 30 Hz, sometimes more as pressure than as sound.

The phase test makes no difference. Is that normal?

On a phone or a single speaker, both channels are often mixed to mono: the out-of-phase signal then almost cancels out and becomes very quiet.

Is any sound sent anywhere?

No. It is produced on your device, with no file and no connection. Only the "Volume" slider level is stored in your browser.