Work out voltage, current, resistance and power
This Ohm's law calculator links the four basic quantities of a circuit: voltage V in volts, current I in amps, resistance R in ohms and power P in watts. Enter any two and it finds the other two. It picks the right formula out of the twelve possible ones, shows it, and highlights it on the formula wheel.
Four more tabs cover the jobs that usually come next: "Series / parallel", "Voltage divider", "LED resistor" and "Energy and cost".
How to use it
- On the "Ohm's law" tab, fill in two of "Voltage V", "Current I", "Resistance R" and "Power P". Leave the other two empty.
- Pick the unit next to each box: mV, V or kV; µA, mA or A; Ω, kΩ or MΩ; mW, W or kW. Results get the most readable prefix automatically.
- Read the results table and the "Formulas used" box. "Clear" empties all four boxes.
The Ohm's law formulas
Ohm's law is V = I × R, and power is P = V × I. Combining the two gives the twelve formulas on the wheel, such as R = V² ÷ P or I = √(P ÷ R).
- 12 V and 2 A give 6 Ω (12 ÷ 2) and 24 W (12 × 2).
- A 2,000 W heater on a 230 V supply draws 2,000 ÷ 230 = about 8.7 A (8.696 A on screen); its hot resistance is 230² ÷ 2,000 = 26.45 Ω.
- With prefixes: 3 mA through 4.7 kΩ gives 4,700 × 0.003 = 14.1 V and 42.3 mW.
The same maths explains everyday limits. A US 15 A circuit at 120 V carries at most 1,800 W, which is why a 1,500 W space heater and a hair dryer on one circuit trip the breaker. In the UK, a 13 A plug fuse at 230 V allows just under 3,000 W.
Series, parallel and voltage dividers
In series, resistances add up: 1 kΩ, 2.2 kΩ and 4.7 kΩ make 7.9 kΩ. In parallel, you add the reciprocals: the same three resistors give about 599.8 Ω. For two resistors, the shortcut is R1 × R2 ÷ (R1 + R2): 100 Ω ∥ 220 Ω = 22,000 ÷ 320 = 68.75 Ω, always less than the smallest one.
A voltage divider follows Vout = Vin × R2 ÷ (R1 + R2). A 9 V battery with two 10 kΩ resistors gives 4.5 V, with 0.45 mA flowing through the pair. That figure assumes no load on the output.
LED resistors and running costs
An LED always needs a series resistor: R = (Vs − Vf) ÷ I. From 5 V, with a red LED at Vf = 2 V and 20 mA, you get (5 − 2) ÷ 0.02 = 150 Ω, which is a standard E12 value. The resistor dissipates 3 × 0.02 = 0.06 W (60 mW), so a 1/4 W part is plenty. With three red LEDs on 12 V, the exact value is 300 Ω; the tool suggests 330 Ω from E12 (18.2 mA in practice) and 300 Ω from E24.
The "Energy and cost" tab multiplies power by time: 2,000 W for 3 hours is 6 kWh, so $1.02 a day at $0.17 per kWh.
Mains voltage is dangerous. These figures help you understand and plan small low-voltage projects; they do not replace a qualified electrician.
FAQ
Why does it need exactly two values?
Two quantities fix the other two. With three, they could contradict each other, so leave the ones you are looking for empty, or press "Clear".
How do I enter 4.7 kΩ or 20 mA?
Type 4.7 and choose kΩ from the list, or 20 and mA. Both a dot and a comma work as the decimal mark.
What are the E12 and E24 series?
They are the standard resistor values sold in shops: 12 or 24 values per decade (10, 12, 15, 18, 22…). The tool shows the nearest one above your result.
Does Ohm's law work with AC?
Yes for resistive loads such as heaters, kettles and toasters. For motors and power supplies, the power factor changes the real current, so treat the result as an estimate.