SuperDevTools

Pool chemical calculator: chlorine, pH and alkalinity doses

1. Pool volume

Water volume —

2. Water test results

Optional fields: leave blank anything you did not test. 1 mg/L = 1 ppm.

Not tested

Ideal: 1 – 3 mg/L

Not tested

Ideal: 7.2 – 7.6

Not tested

Ideal: 80 – 120 mg/L

Not tested

Ideal: 30 – 50 mg/L

3. Doses to add, in this order

1 Total alkalinity

2 pH

3 Chlorine

4 Shock (superchlorination to 10 ppm)

5 Stabilizer (cyanuric acid)

Product strength

Liquid chlorine convention: a percentage is read by weight with a density of 1.2, so 12.5% = 150 g of available chlorine per liter. A jug sold as 12.5% trade strength holds 125 g per liter: choose g/L and type 125. Acid density estimated at 1 + 0.005 × %.

Safety rules
  • Never mix two products, not even two kinds of chlorine: add them separately, several hours apart.
  • Always add the product to the water, never water to the product.
  • Wear gloves and goggles, work outdoors, keep children away.
  • After a shock, no swimming until free chlorine is back under about 3 ppm.
  • Follow the product label: it takes precedence over these estimates.

Calculated in your browser. The volume and product strengths stay on this device.

How much chlorine does your pool need?

This pool chemical calculator starts from the volume of water in your pool and your test results (free chlorine, pH, total alkalinity, stabilizer) and tells you how much of each product to add, in grams, ounces, milliliters or fluid ounces. It covers calcium hypochlorite shock granules, slow trichlor tablets, liquid chlorine, a full shock to 10 ppm, dry acid, muriatic acid, soda ash, baking soda and cyanuric acid. A green, orange or red dot next to each reading shows at a glance whether it sits in the ideal range.

How to use it

  1. Under "Units", pick "feet and US gallons" or "meters, m³ and liters".
  2. In "1. Pool volume", choose "the dimensions" or "the volume". For dimensions, set the "Pool shape" (rectangular, round, oval or kidney), then the "Average depth" or the "Shallow end" and "Deep end".
  3. Check the "Water volume", shown in m³, liters and US gallons.
  4. In "2. Water test results", type the readings from your test kit. Leave blank anything you did not test: the tool then gives a reference dose.
  5. Adjust the "Target free chlorine", "Target pH" and "Target alkalinity" if you wish, and read "3. Doses to add, in this order". Under "Product strength", enter the percentage printed on your containers.

Water balance in four readings

Free chlorine kills germs: aim for 1 to 3 ppm (1 ppm = 1 mg/L). pH should stay between 7.2 and 7.6: above that, chlorine works poorly and scale forms; below it, the water stings eyes and corrodes metal parts. Total alkalinity is the buffer that keeps pH steady, ideally 80 to 120 ppm. Stabilizer (cyanuric acid, CYA) shields chlorine from sunlight and belongs between 30 and 50 ppm.

Correct in this order: alkalinity, pH, then chlorine

Fix alkalinity first, because it decides how stable the pH will be. Then adjust pH, and only then chlorine, which works best at the right pH. Run the pump a few hours between two products.

Worked examples

A 10,000-gallon pool holds 37.85 m³. Every 1 ppm of chlorine in 1 m³ is 1 g of available chlorine, so +1 ppm takes 37.85 g:

  • Shock granules at 65%: 37.85 ÷ 0.65 = 58.2 g (2.1 oz).
  • Liquid chlorine sold as 12.5% trade strength (125 g per liter): 303 ml (10.2 fl oz).
  • Shock from 0 to 10 ppm: 378.5 g of available chlorine, which is 582 g (1.28 lb) of granules or 3.03 L (0.80 gal) of that liquid.
  • Alkalinity from 80 to 100 ppm: 20 × 1.68 g × 37.85 m³ = 1.27 kg (2.80 lb) of baking soda.
  • pH from 7.8 to 7.4 at 100 ppm alkalinity: about 757 g (26.7 oz) of dry acid.

A metric example: an 8 × 4 m pool with a 1.5 m average depth holds 48 m³, or 12,680 gallons. Raising chlorine by 1 ppm takes 48 ÷ 0.65 = 73.8 g of granules. A round above-ground pool 15 ft across with 4 ft of water holds about 5,290 gallons.

How the numbers are worked out

Liquid chlorine strength can be read two ways. With "% by weight", the tool assumes a density of 1.2, so 12.5% means 150 g of available chlorine per liter. Many jugs sold in North America state a trade percentage, which is already grams per 100 ml: for those, set "Liquid chlorine unit" to g/L and type 125 for 12.5%.

For pH, the tool starts from 50 g of dry acid or 25 g of soda ash per 10 m³ (about 2,640 gallons) and per 0.1 pH at 100 ppm alkalinity, scaled to your alkalinity: at 150 ppm the dose goes up by half. Treat it as an approximation. Add half, run the pump a few hours, retest, then top up. A kidney pool is estimated as 0.45 × (wide end + narrow end) × length.

How often to test

During the season, test chlorine and pH two or three times a week, and daily in a heat wave, after a storm or a busy pool party. Check alkalinity every two weeks and stabilizer once a month: it never evaporates and builds up, especially with trichlor tablets.

Safety

Never mix two products, not even two kinds of chlorine: the mix can release toxic gas. Always add chemicals to water, never water to chemicals. Wear gloves and goggles and follow the label. After a shock, keep everyone out until free chlorine is back under about 3 ppm.

Frequently asked questions

How much shock for a 20,000-gallon pool?

To shock to 10 ppm from zero: 75.7 m³ × 10 = 757 g of available chlorine, which is 1.16 kg (2.57 lb) of 65% granules or 6.06 L (1.60 gal) of liquid chlorine at 125 g per liter.

Why adjust alkalinity before pH?

Low alkalinity lets pH swing with every addition; high alkalinity locks it in place. Until alkalinity sits between 80 and 120 ppm, pH corrections do not hold.

When can you swim after shocking a pool?

Once free chlorine has dropped below about 3 ppm, usually after 12 to 48 hours of running the pump. Test before anyone gets in.

What if stabilizer is above 75 ppm?

Only replacing part of the water brings it down. The tool works out the share: from 90 to 50 ppm, replace 44% of the water. Then switch to an unstabilized chlorine.